Purchase Solution

Design a resistor that carries a current of 5mA with applied voltage of 5V

Not what you're looking for?

Ask Custom Question

An n-type Si resistor is to be designed so that it carries a current of 5mA with an applied voltage of 5V. T=300K. Mn*=.26M0. M0=9.11x10^31Kg.

(a) If Nd=10^15/cm^3 and Na=0, design a resistor to meet the required specifications.
(b) If Nd=3x10^16/cm^3 and Na=2.5x10^16/cm^3, redesign the resistor.

What are the answers and how did you calculate them?

Purchase this Solution
Solution Summary

The solution carefully explains and designs a resistor that carries a current of 5mA with applied voltage of 5V.

Solution Preview

The problem gave you Mn, it looks like it wants you to get electron/hole mobility from effective electron/hole mass and mean scattering time. However, the mean scattering time is not ...

Purchase this Solution
Free BrainMass Quizzes
The Moon

Test your knowledge of moon phases and movement.

Classical Mechanics

This quiz is designed to test and improve your knowledge on Classical Mechanics.

Intro to the Physics Waves

Some short-answer questions involving the basic vocabulary of string, sound, and water waves.

Introduction to Nanotechnology/Nanomaterials

This quiz is for any area of science. Test yourself to see what knowledge of nanotechnology you have. This content will also make you familiar with basic concepts of nanotechnology.

Basic Physics

This quiz will test your knowledge about basic Physics.

View More Free Quizzes
Related BrainMass Solutions

  • NMOS FET and BJT analysis

    To design the circuit, the emitter is connected to ground, the MCU output pin is connected to the base with a 10kΩ resistor in between, the 5V supply is connected to the anode of the LED in series with a 220Ω resistor, and the cathode of the LED is connected

  • Problem on how to find the voltage gain of the amplifier

    22351 Problem on how to find the voltage gain of the amplifier A power amplifier when driven by a current source of 5mA rms and a source resistance of 8k, delivers 12.5W signal power to an 8k load resistance.

  • Voltage divider

    51202 Voltage Divider We want to design a voltage divider circuit to provide an output voltage Vo=5V from a 12V source as shown in the attachment problem, the current taken from the 12 V source is to be 100mA. Find values of R1 and R2.

  • Power Amplifiers and RMS Value Calculations

    22334 Power Amplifiers and RMS Value Calculations A power amplifier when driven by a current source of 5mA rms and a source resistance of 8k, delivers 12.5 W signal power to an 8 load resistance. Find rms value of the output voltage.

  • Transistor Voltages


    The voltage level at the base is thus 0 V (one end of the 10 kilo-ohm resistor) - 10 kilo-ohm * 0.0035 mA (voltage drop across resistor) = -0.035 V.
    Vbase is thus -0.035 V.

  • Resistors: Explanations and Calculations

    First, how do calculate or get a resistor with this information to both limit the current for each circuit and make sure I get the right voltage for each circuit and then run each one at a time and then all at once.

  • Circuit analysis with LEDs, BJTs, Relays, Opto Couplers

    625925 Circuit analysis with LEDs, BJTs, Relays, Opto Couplers (b) The diagram of FIGURE 2 shows a bi-directional opto coupler input interface circuit. When a supply voltage of 20 V is applied the LED carries a current and 2 V is dropped across it.

  • Electric Circuits

    421850 Electric Circuits Resistors A circuit consists of two 100 ohm resistors in series. What is the voltage across each resistor when a. The current through the resistors is 10 mA? b. The current through the resistors is 50 mA?

  • Theveninization of a transistor circuit

    So we can represent all that junk by a voltage source of 2.5V in series with a resistance of 10 ohms, connected to the base.

View More Related Solutions